| eneral
parameters |
Model | BJPX-3101 | |
| Power Supply | AC220-230V/50Hz,1300VA | ||
| Maximum heater output power | 350W/240V | ||
| Auxiliary power output | AC220-230V/50Hz,3A | ||
| Heater instructions | 0～100% | ||
| Temperature control mode | Box temperature mode; infant mode | ||
| Box temperature control temperature range | 25～37℃；37～39℃(Leapfrogging Mode) | ||
| Skin temperature control temperature range | 34～37℃37～38℃（Leapfrogging Mode） | ||
| Sensor temperature display range | 5～65℃ | ||
| Warm-up time(ambient temperature is generally + 22 ℃)* |
No more than 40 minutes
|
||
| Temperature variability* | No more than 0.5℃ | ||
| Temperature uniformity * (the mattress is in a horizontal position) | No more than 0.8℃ | ||
| Temperature uniformity * (the mattress is in an inclined position) | No more than 1.0℃ | ||
| The difference between average incubator temperature and control temperature | No more than 1.0℃ | ||
| Skin temperature sensor accuracy | ±0.2℃ | ||
| Humidity
control |
The running time of the water tank is filled with distilled water after | Humidity below 70%RH, at least 24 hours | |
| Tank capacity | 1200ml | ||
| Humidity display range | 0%RH～99%RH | ||
| Humidity control range | 0%～90%（Adjust 1% each time） | ||
| Humidity control precision | ±5%RH | ||
| Humidity display accuracy
(ambient temperature 25℃, ambient humidity 45%RH + 5% RH) |
±5%RH | ||
| Note: in the context of a fairly high ambient humidity, it may not be possible to achieve a
relatively low humidity control |
|||
| Oxygen
concentration control |
Oxygen concentration display range | 0%～99% | |
| Oxygen concentration display resolution | 1% | ||
| Oxygen concentration display accuracy | ±2% O?(The oxygen concentration set value of less than25%)
±3% O?(The oxygen concentration set value of more than 25%) |
||
| Oxygen concentration control accuracy | ±4%O?Concentration within the volume | ||
| Oxygen concentration setting range | 20%～60%（Adjust 1% each time） | ||
| Oxygen sensor service life | Use up to 10,000 hours at 100% oxygen concentration | ||
| Ambient
temperature |
The scope of work | +20～+30℃ | |
| Transportation and storage | -20～+55℃ | ||
| (suggested that the user should not be used in an environment outside the specified range) | |||
| Relative humidity | Relative humidity operating range | 30%～75%RH | |
| Transportation and storage | No more than 93%RH | ||
| Note 🙁 not recommended to be used outside the specified range of environments) | |||
| Atmospheric pressure | Transport and storage atmospheric pressure range | 500hPa～1060hPa | |
| Working atmospheric pressure range | 800hPa～1060hPa | ||
| Applicable Environment Altitude | ≤2000m | ||
| Overvoltage category | Ⅱ | ||
| Pollution Level |
2 |
||
| Air flow rate | Ambient air flow rate | Less than 0.3m/s | |
| Other indicators | Ambient noise in constant temperature enclosure | The stable temperature is not more than 45dB (A)
In other states is not more than 50dB (A) Ambient noise is not more than 35dB (A) |
|
| Ambient carbon dioxide concentration in constant temperature enclosure | Carbon dioxide gas mixture is injected at the
speed of 750ml/minute right above the mattress about 10cm, the density should be under 0.5%. |
||
| Air velocity above the crib mattress | No more than0.35m/s | ||
| General alarm |
Power off alarm, fan alarm, sensor alarm, deviation alarm, over temperature alarm, sensor box placement error alarm, water tank placement error alarm, water shortage alarm
|
||
| System alarm | ROM alarm, internal alarm system,SRAM alarm, EEPROM alarm, real-time alarm,
communication alarm, ADC alarm, keyboard alarm, battery alarm, LCD display alarm, temperature heating system alarm, humidity heating system alarm |
||
| Note: please refer to the contents of the relevant terms and markers. | |||
Incubator
Infant Incubator
| eneral
parameters |
Model | BJPX-3101 | |
| Power Supply | AC220-230V/50Hz,1300VA | ||
| Maximum heater output power | 350W/240V | ||
| Auxiliary power output | AC220-230V/50Hz,3A | ||
| Heater instructions | 0～100% | ||
| Temperature control mode | Box temperature mode; infant mode | ||
| Box temperature control temperature range | 25～37℃；37～39℃(Leapfrogging Mode) | ||
| Skin temperature control temperature range | 34～37℃37～38℃（Leapfrogging Mode） | ||
| Sensor temperature display range | 5～65℃ | ||
| Warm-up time(ambient temperature is generally + 22 ℃)* |
No more than 40 minutes
|
||
| Temperature variability* | No more than 0.5℃ | ||
| Temperature uniformity * (the mattress is in a horizontal position) | No more than 0.8℃ | ||
| Temperature uniformity * (the mattress is in an inclined position) | No more than 1.0℃ | ||
| The difference between average incubator temperature and control temperature | No more than 1.0℃ | ||
| Skin temperature sensor accuracy | ±0.2℃ | ||
| Humidity
control |
The running time of the water tank is filled with distilled water after | Humidity below 70%RH, at least 24 hours | |
| Tank capacity | 1200ml | ||
| Humidity display range | 0%RH～99%RH | ||
| Humidity control range | 0%～90%（Adjust 1% each time） | ||
| Humidity control precision | ±5%RH | ||
| Humidity display accuracy
(ambient temperature 25℃, ambient humidity 45%RH + 5% RH) |
±5%RH | ||
| Note: in the context of a fairly high ambient humidity, it may not be possible to achieve a
relatively low humidity control |
|||
| Oxygen
concentration control |
Oxygen concentration display range | 0%～99% | |
| Oxygen concentration display resolution | 1% | ||
| Oxygen concentration display accuracy | ±2% O?(The oxygen concentration set value of less than25%)
±3% O?(The oxygen concentration set value of more than 25%) |
||
| Oxygen concentration control accuracy | ±4%O?Concentration within the volume | ||
| Oxygen concentration setting range | 20%～60%（Adjust 1% each time） | ||
| Oxygen sensor service life | Use up to 10,000 hours at 100% oxygen concentration | ||
| Ambient
temperature |
The scope of work | +20～+30℃ | |
| Transportation and storage | -20～+55℃ | ||
| (suggested that the user should not be used in an environment outside the specified range) | |||
| Relative humidity | Relative humidity operating range | 30%～75%RH | |
| Transportation and storage | No more than 93%RH | ||
| Note 🙁 not recommended to be used outside the specified range of environments) | |||
| Atmospheric pressure | Transport and storage atmospheric pressure range | 500hPa～1060hPa | |
| Working atmospheric pressure range | 800hPa～1060hPa | ||
| Applicable Environment Altitude | ≤2000m | ||
| Overvoltage category | Ⅱ | ||
| Pollution Level |
2 |
||
| Air flow rate | Ambient air flow rate | Less than 0.3m/s | |
| Other indicators | Ambient noise in constant temperature enclosure | The stable temperature is not more than 45dB (A)
In other states is not more than 50dB (A) Ambient noise is not more than 35dB (A) |
|
| Ambient carbon dioxide concentration in constant temperature enclosure | Carbon dioxide gas mixture is injected at the
speed of 750ml/minute right above the mattress about 10cm, the density should be under 0.5%. |
||
| Air velocity above the crib mattress | No more than0.35m/s | ||
| General alarm |
Power off alarm, fan alarm, sensor alarm, deviation alarm, over temperature alarm, sensor box placement error alarm, water tank placement error alarm, water shortage alarm
|
||
| System alarm | ROM alarm, internal alarm system,SRAM alarm, EEPROM alarm, real-time alarm,
communication alarm, ADC alarm, keyboard alarm, battery alarm, LCD display alarm, temperature heating system alarm, humidity heating system alarm |
||
| Note: please refer to the contents of the relevant terms and markers. | |||
Based on 0 reviews
Be the first to review “Infant Incubator”
You must be logged in to post a review.
Related products
-
Incubator
Climate Incubator BJPX-A Series
Safety function:
1.Over temperature protection.
2.Temperature sensor for open circuit or short circuit protection.
3.Auto-off protection and alarm for abnormal situation.
4.Parameters can be saved automatically when power off or system error.
Temperature/Humidity area table.
Blue area: Illumination on, 18~45°C/50%~80%RH
Red area: Illumination off, 14~45°C/50%~90%RH
SKU: CP4375 -
-
Incubator
Climate Incubator BJPX-A1000C/BJPX-A1500C
Feature:
1.The shell is made from fashion aluminium alloy, beautiful and easy, internal use mirror stainless steel production, four corners round solitary processing, can adjust clapboard, the user operation more simple.
2.Adopted advanced MCU programmable technology temperature control, can be installed incubator of various parameters (including temperature and light).
3.Using hollow reflection tempered coating glass, adiabatic performance is good beautiful and easy.
4.Reliable security, instrument has many make interference measures, and have overtemperature protection heat, thermal resistance short-circuit protection, compressor delay protection.
5.Dosing multispectral when the mouth plant growth lamp, be helpful for culture growth, improve make disease resistance.
6.Imported compression, stainless steel water jacket. Digital display, microcomputer automatic control.
7.Microcomputer control, timing or continuity work party or can choose, multiple programmable control, can be customized 30 period of temperature, humidity, Settings, humidity for 10-90% RH.
8.Type A: each surface 3 root plant lamp (2 surface); Type B: each surface 9 root plant lamp (2 surface); Type C: each surface 12 root plant lamp (2 surface) ;Type D: each surface 12 root plant lights (3 surface).
9.With light, heat and cold day and night temperature, automatic switching procedures and overtemperature protection to simulate the natural climate.
10.Humidifying range 40-90% RH (depending on the temperature and decide), humidity automatic control.
Technical Parameter:
Model BJPX-A1000C BJPX-A1500C Volume 1000L 1500L Environmental conditions Temperature 0-50℃ Maximum relative humidity <80% Altitude<2000M Illumination power 22000LUX 22000LUX Power voltage AC220±10V,50HZ±1HZ Temperature range 5℃-60℃ Humidity control range 40-90%RH Humidity sensor HM1500 Temperature Accuracy 0.1℃ Volatility ±0.5℃ Uniformity ±0.5℃ Controller Digital display,touch,microprocessor temperature control with fuzzy PID control technology Sensor PT100 Time 0-9999min Humidifier external Material Internal Mirror stainless steel External Aluminium alloy Size Internal 1300×640×1250 1960×640×1250 External 1400×690×1985 2020×700×1980 Light intensity(lx) 22000 (2 surface) 22000 (2 surface) Power consumption 2100 2180 Rack position 6 9 SKU: CP4370 -
Incubator
Constant Temperature and Humidity Incubator
The working chamber adopt the round angle structure , easy to clean.
Microprocessor temperature control.
LED display for BJPX-HT series, LCD display for BJPX-HTII series.
The starting up time can be preset.
Electrical power outlet in the chamber.
UV light for sterilization.
Double door design and magnetic door sealing.
Universal Castors for easy movement.
CFC-free refrigerant with high efficiency.
Safety function:
Over temperature protection, temperature sensor malfunction alarm.
Parameters can be saved automatically when power off or system error.
High and low water level alarm. Automatic heating off for low water level.
Notice: Please don’t ues in low temperature (≤20°C) for long time (≥160h).
Model BJPX-HT150 BJPX-HT150II
BJPX-HT200 BJPX-HT200II
BJPX-HT250 BJPX-HT250II
BJPX-HT300 BJPX-HT300II
BJPX-HT400 BJPX-HT400II
Capacity 160L 200L 250L 300L 400L Temp. Range 0~65°C Temp. Fluctuation ±1 °C Temp. Stability/Uniformity ±2 °C Humidity Range 50~90% RH (±5~8% RH) Sterilization Type UV lamp Shelves 3pcs/adjustable Consumption 300W 350W 430W 480W 750W Power Supply AC110/220V±10%, 50/60Hz Standard Accessory Micro printer(for HTII series), humidifier Internal Size(W*D*H)mm 450*420*850 450*450*1000 480*490*1070 520*500*1170 580*540*1270 External Size(W*D*H)mm 590*620*1400 590*640*1550 620*680*1620 660*690*1720 720*740*1820 Packing Size(W*D*H)mm 750*780*1600 750*800*1740 780*840*1810 820*850*1910 880*900*2010 Gross Weight(kg) 120 138 147 157 170 SKU: CP4373
There are no reviews yet.