| eneral
parameters |
Model |
BJPX-3101 |
| Power Supply |
AC220-230V/50Hz,1300VA |
| Maximum heater output power |
350W/240V |
| Auxiliary power output |
AC220-230V/50Hz,3A |
| Heater instructions |
0～100% |
| Temperature control mode |
Box temperature mode; infant mode |
| Box temperature control temperature range |
25～37℃；37～39℃(Leapfrogging Mode) |
| Skin temperature control temperature range |
34～37℃37～38℃（Leapfrogging Mode） |
| Sensor temperature display range |
5～65℃ |
| Warm-up time(ambient temperature is generally + 22 ℃)* |
No more than 40 minutes
|
| Temperature variability* |
No more than 0.5℃ |
| Temperature uniformity * (the mattress is in a horizontal position) |
No more than 0.8℃ |
| Temperature uniformity * (the mattress is in an inclined position) |
No more than 1.0℃ |
| The difference between average incubator temperature and control temperature |
No more than 1.0℃ |
| Skin temperature sensor accuracy |
±0.2℃ |
| Humidity
control |
The running time of the water tank is filled with distilled water after |
Humidity below 70%RH, at least 24 hours |
| Tank capacity |
1200ml |
| Humidity display range |
0%RH～99%RH |
| Humidity control range |
0%～90%（Adjust 1% each time） |
| Humidity control precision |
±5%RH |
| Humidity display accuracy
(ambient temperature 25℃, ambient humidity 45%RH + 5% RH) |
±5%RH |
| Note: in the context of a fairly high ambient humidity, it may not be possible to achieve a
relatively low humidity control |
| Oxygen
concentration
control |
Oxygen concentration display range |
0%～99% |
| Oxygen concentration display resolution |
1% |
| Oxygen concentration display accuracy |
±2% O?(The oxygen concentration set value of less than25%)
±3% O?(The oxygen concentration set value of more than 25%) |
| Oxygen concentration control accuracy |
±4%O?Concentration within the volume |
| Oxygen concentration setting range |
20%～60%（Adjust 1% each time） |
| Oxygen sensor service life |
Use up to 10,000 hours at 100% oxygen concentration |
| Ambient
temperature |
The scope of work |
+20～+30℃ |
| Transportation and storage |
-20～+55℃ |
| (suggested that the user should not be used in an environment outside the specified range) |
| Relative humidity |
Relative humidity operating range |
30%～75%RH |
| Transportation and storage |
No more than 93%RH |
| Note 🙁 not recommended to be used outside the specified range of environments) |
| Atmospheric pressure |
Transport and storage atmospheric pressure range |
500hPa～1060hPa |
| Working atmospheric pressure range |
800hPa～1060hPa |
| Applicable Environment Altitude |
≤2000m |
| Overvoltage category |
Ⅱ |
| Pollution Level |
2 |
| Air flow rate |
Ambient air flow rate |
Less than 0.3m/s |
| Other indicators |
Ambient noise in constant temperature enclosure |
The stable temperature is not more than 45dB (A)
In other states is not more than 50dB (A)
Ambient noise is not more than 35dB (A) |
| Ambient carbon dioxide concentration in constant temperature enclosure |
Carbon dioxide gas mixture is injected at the
speed of 750ml/minute right above the mattress about 10cm, the density should be under 0.5%. |
| Air velocity above the crib mattress |
No more than0.35m/s |
| General alarm |
Power off alarm, fan alarm, sensor alarm, deviation alarm, over temperature alarm,
sensor box placement error alarm, water tank placement error alarm, water shortage alarm
|
| System alarm |
ROM alarm, internal alarm system,SRAM alarm, EEPROM alarm, real-time alarm,
communication alarm, ADC alarm, keyboard alarm, battery alarm, LCD display alarm,
temperature heating system alarm, humidity heating system alarm |
| Note: please refer to the contents of the relevant terms and markers. |
There are no reviews yet.